Thanks Joe, I do not think I quite understand "further acceleration can be applied only at PP#1" in 10-19-C. Is this what you mentioned?
I think what HK means in 10-19-C, is that any further acceleration applied at PP#1 has to be a pull along the shaft, because if you push on #1 with the right triceps, you would preempt cf, and be switting. That's the only sense I can make of it.
Location: Near a golf course...no, beside a golf course...
Posts: 51
Originally Posted by MizunoJoe
I think what HK means in 10-19-C, is that any further acceleration applied at PP#1 has to be a pull along the shaft, because if you push on #1 with the right triceps, you would preempt cf, and be switting. That's the only sense I can make of it.
Maybe HK meant really PA1 use when CF has already started releasing?
In any case, HK prefers 4-1-2-3...could there be any swinging element with 4-1-2-3? None, yah? This is pure hitting, correct?
Then further acceleration can be applied only at Pressure Point #1 to support the Pull on the Clubshaft - especially for Short Shot Power.
That sentence from 10-19-C refers to the third paragraph in 10-11-0 (citing from the 6th edition).
You apply acceleration at PP#1 to actuate the Primary Lever Assembly (accelerate the Left Arm, basically). But the Secondary Lever Assembly (the Club) is actuated by Centrifugal Force alone (Release of Accumulators #2 and/or #3).
And no, this a Swinging procedure. No Hitting. No Switting.
That sentence from 10-19-C refers to the third paragraph in 10-11-0 (citing from the 6th edition).
You apply acceleration at PP#1 to actuate the Primary Lever Assembly (accelerate the Left Arm, basically). But the Secondary Lever Assembly (the Club) is actuated by Centrifugal Force alone (Release of Accumulators #2 and/or #3).
And no, this a Swinging procedure. No Hitting. No Switting.
This must be done with the right shoulder and not the right triceps, so the part of the sentence in 10-18-C, which is confusing is "further acceleration", which implies something else was accelerating PP#1 earlier. That could only be the right triceps. In a 3-barrel Swing only the driving right shoulder should be applying acceleration at PP#1.
This must be done with the right shoulder and not the right triceps, so the part of the sentence in 10-18-C, which is confusing is "further acceleration", which implies something else was accelerating PP#1 earlier. That could only be the right triceps. In a 3-barrel Swing only the driving right shoulder should be applying acceleration at PP#1.
Not sure what you mean by applying acceleration at PP#1 with the right shoulder.
I think that sentence from 10-19-C refers to the use of Accumulator #1. That's not a 4-2-3 Triple Barrel Swing.
You can add acceleration to the Primary Lever Assembly with the Right Arm (Accumulator #1) - as long as you don't actuate the Secondary Lever Assembly (the Club) with the Right Arm, as long as you don't drive the Club with the Right Arm, the Secondary Lever Assembly is still being pulled longitudinally by the Left Arm, and it's still a Swing.
Not sure what you mean by applying acceleration at PP#1 with the right shoulder.
I think that sentence from 10-19-C refers to the use of Accumulator #1. That's not a 4-2-3 Triple Barrel Swing.
You can add acceleration to the Primary Lever Assembly with the Right Arm (Accumulator #1) - as long as you don't actuate the Secondary Lever Assembly (the Club) with the Right Arm, as long as you don't drive the Club with the Right Arm, the Secondary Lever Assembly is still being pulled longitudinally by the Left Arm, and it's still a Swing.
Since #1 is used, does it become 4 barrel? And since 4 Barrel is a hitting procedure, it becomes 4 barrel hitting?
Or it means using #1 passively (not actively for straightening the right arm), it still a 3 barrel therefore swinging?
Since #1 is used, does it become 4 barrel? And since 4 Barrel is a hitting procedure, it becomes 4 barrel hitting?
Or it means using #1 passively (not actively for straightening the right arm), it still a 3 barrel therefore swinging?
4 Barrel is not necessarily Hitting. A Swinging Procedure can also be 4 Barrel. Homer Kelley had a sample pattern for a 4 Barrel Swinging Procedure in the 3rd edition of the book.
Accumulator #1 participation in a 4 Barrel Swing is active direct drive at PP#1. That's what the "except per 2-M-3" at the end of 10-11-0-1 tries to express.
Hybrid Mode
