Hogan and EA

[Daryl]

I'm saying that my hands slow because of Throw-out. I don't always have that amount of precision. But when I do, the Hand slows and I'm forced to push a little. I'm not pushing against the #3 PP. I feel the Slowdown with my Right Hand. I'm pushing with the Palm of the Right Hand to resist the Slow-down.

[HungryBear]

I'm saying that my hands slow because of Throw-out. I don't always have that amount of precision. But when I do, the Hand slows and I'm forced to push a little. I'm not pushing against the #3 PP. I feel the Slowdown with my Right Hand. I'm pushing with the Palm of the Right Hand to resist the Slow-down.

I think (AGAIN just me thinking) that is exactly it. the trying to keep hands moving. I think that is why Hogan wanted more hands



HB

[Daryl]

I think (AGAIN just me thinking) that is exactly it. the trying to keep hands moving. I think that is why Hogan wanted more hands



HB

Then we're on the same page. I hope it's the right one.

[BerntR]

I love that super heavy inertia feeling.

I push with pp#1. But that's hardly a secret by now

Unfortunately I am not able to pruduce that kind of action on every stroke. Far from it.

[JerryG]

Thanks for this discussion. I am taking it in and ruminating.
Some time ago I was trying to really stress pp#1 and usually liked the feel as well as the fact I was maintaining my flying wedges and some lag for the first time in my life. Sometimes shots would be a bit to the right and in the beginning that didn't matter since I was striking it so well, but it then became a concern.
Focusing a little more on #3 straightened things out quite a bit and I have been actually hitting more targets, greens especially, than ever before.
Then I noticed my left hand was getting a little too weak and my grip alignments were a little off. If it isn't one thing, its another. I am not complaining though, because now I actually have a bit of a clue what to do to make a correction instead of a compensation.
Geez, I love this TGM stuff.

[O.B.Left]

I believe Mr Hogan is describing what we would term Indirect Drive, Inertia , Lag Pressure at the index finger, on the aft of the shaft , associated with Radial Acceleration.

[Daryl]

I believe Mr Hogan is describing what we would term Indirect Drive, Inertia , Lag Pressure at the index finger, on the aft of the shaft , associated with Radial Acceleration.

I can't get that term "Indirect Drive" in my head. Would you help explain the differences between "Direct" and "Indirect Drive" in the Sections below?

10-11-0-1 PRESSURE POINT #1 (above) is active Power Package “direct drive” (7-11) of Accumulator #1 for actuating the Primary Lever Assembly (6-2-A) for Hitting (10-19-A) as well as Extensor Action (6-B-1-D). It is Loaded (7-22) per 6-B-1-0 and 7-19-1. It is only a passive “direct drive” with any true Swing procedure – Right Arm (7-19) or Left (6-B-3-0) – except per 2-M-3.

10-11-0-2 PRESSURE POINT #2 (above) actuates the Secondary Lever Assembly (6-B-2), normally, only as “Passive Clubhead Lag” (6-C-2-A). It is Loaded (7-22) per 6-B-2 and 7-19-3 and is a Swinger’s Rope Handle application (2-K, 2-M-3).

10-11-0-3 PRESSURE POINT #3 (above) can be either active or passive (6-C-2-A) Accumulator #1 indirect drive (7-11) of the Secondary Lever Assembly (6-A-3) (2-K). That is, actively as Accumulator #2 Axe Handle application for Hitting (10-3-K, 10-19-A) but passively as Accumulator #3 (6-B-3-0, 10-19-C) or with a Right Arm Swing (7-19). Lag Loading (10-19) and Delivery Line (2-J-3) requirements. It is Loaded (10-22) per 7-19 as required by Component 19 application being employed (10-19). Study 2-G and 6-C.